Oil Spill Kit Guide for NZ Workplaces: Contents and Use

An oil spill kit holds the protective gear, absorbents, containment and waste containers needed to stop a spill spreading and clean it up safely. To be useful, it has to be sized for the largest spill you could realistically have, packed with materials suited to oil, kept where people can reach it, and restocked after every use. This guide covers what to pack, how to choose a size, how to use the kit and how to keep it ready. Safewell supplies spill kits and spill management supplies across New Zealand for workplaces that want the whole job covered in one order.

Safewell
Prepare Your Workplace for Oil Spills
Safewell supplies spill kits and spill management supplies for workplaces across New Zealand, helping teams prepare for oil spills.

TL;DR

  • A spill kit is a core part of your spill plan if you hold hazardous substances. WorkSafe defines it as the equipment and materials needed to clean up a spill.
  • Size the kit to the maximum likely spill, not the average one. Check the safety data sheet (SDS) for what the substance needs.
  • Every kit needs PPE, a non-sparking shovel and broom, absorbents, drain protection and a leak-proof waste container. Sawdust is not suitable for flammable liquids.
  • Kits suit small spills. A large spill means the emergency plan and a call to 111 and Fire.
  • After any use, replace what was used straight away and review the procedure.

Table of Contents

When a workplace needs an oil spill kit

If you store or handle hazardous substances, you need a plan for containing a spill and knowing how to clean it up. WorkSafe describes a spill kit as a major part of that plan. Diesel, petrol, hydraulic oil, engine oil and many lubricants all fall into this group, so workshops, farms, construction sites, depots, marinas and service stations are the obvious places. A fuel or oil leak in a car park or yard is just as real an issue for a retail site or a community organisation with a vehicle fleet.

The legal footing is the Health and Safety at Work Act 2015. It requires a business or undertaking (a PCBU) to provide and maintain a safe workplace and safe systems of work, including the safe use, handling and storage of substances, so far as is reasonably practicable. The Health and Safety at Work (Hazardous Substances) Regulations 2017 brought the workplace rules for hazardous substances together under that Act, with most of them taking effect on 1 December 2017. The EPA continues to approve substances and set the rules that protect the environment.

The EPA’s guidance on working safely with hazardous substances says that for small spills a kit might be enough to contain the spill. The equipment depends on the substances you hold and the amount that could be spilled. Workers must also know where the kit is kept and how to use it.

When a workplace needs an oil spill kit

Small spill or large spill

A kit is built for small, controllable spills. WorkSafe’s service station guidance says large spills trigger the full emergency response plan and a call to FENZ, because flammable vapours can linger and liquids travel across paved areas into waterways. Decide before an incident where your line sits. A few litres of hydraulic oil from a hose on a workshop floor is a kit job. A ruptured fuel tank is not.

Choosing the right size

The sizing rule is simple. Environment Southland says the kit should be able to handle the maximum likely spill volume. It suggests checking the SDS for the equipment required, then either buying a standard kit or filling a wheelie bin with the items you identify.

Work through it in this order:

  1. List what you hold. Include every oil, fuel and lubricant on site, in drums, tanks, machine reservoirs and vehicles.
  2. Find the largest container that is not already in secondary containment. A drum in a bunded area is protected. A drum on a pallet by the door is not.
  3. Estimate the worst realistic release. A full drum tipped over is a better planning figure than a drip from a fitting.
  4. Match absorbent capacity to that volume. WorkSafe says absorbents should be inert and absorb around half their volume of liquid, and you should hold enough for your largest containers that do not need secondary containment.
  5. Place kits near the risk. A kit locked in an office across the site does little for a leak at the fuel point.

Safewell’s range includes 120L and 240L general purpose spill kits, so you can step the size up to match the volume you calculated. Browse the full spill management category to compare kits against your list.

Oil spill kit contents: the checklist

WorkSafe and the EPA give almost the same checklist, and it is a good base for any oil spill kit. The table sets out each group, what goes in it and what to watch for.

Group What to include Watch for
PPE Gumboots, gloves, overalls, goggles, facemasks or respirators Match gloves and respiratory protection to the SDS
Handling equipment Broom and plastic shovel Metal shovels can spark, which is dangerous with flammable substances
Containment Drain guards, barriers, drip trays or pans, containment socks Block drains and grates first
Absorbents Absorbent pads, spill socks, vermiculite, zeolite, dry sand Sawdust is not suitable for flammable liquids
Waste Leak-proof container, bags or drums, labels Must hold the used absorbent without leaking
Information SDS, basic instructions, contact numbers Workers need to know where the kit is

The PPE, handling, containment, absorbent and waste groups come from WorkSafe’s checklist and the EPA’s checklist.

Protective equipment

Protective gear goes on before anything else. Gloves, goggles, overalls and boots stop oil reaching skin and eyes, and a facemask or respirator is needed where vapours are a concern. The SDS tells you which type suits the product. If your team also covers health or first responder work, this PPE survey for healthcare workers and first responders shows how protective equipment needs are commonly reviewed. Safewell’s Spill Kit Accessory Pack covers PPE and clean-up essentials, which suits a kit that needs topping up rather than replacing.

Absorbents and containment

Absorbent pads, socks and loose material do different jobs. Pads and loose absorbent soak up liquid on a surface. Containment socks are fabric tubes filled with an absorbent such as vermiculite. WorkSafe says they are used to soak up spills before they spread or to keep them from reaching stormwater. Drain guards and barriers matter just as much, because most of the harm from an oil spill happens when it reaches a drain.

Roles of oil spill absorbents and drain protection

One point catches people out. Sawdust looks like a cheap fix, but the EPA warns it is not suitable for flammable or oxidising substances because it acts as a fuel in a fire. For fuel spills, WorkSafe’s service station guide names sand or kitty litter as suitable loose absorbents and again flags sawdust as unsuitable.

Waste containers and labels

The used absorbent is now contaminated waste and needs a leak-proof container. Pack bags or a lidded drum, and keep a label on the kit so people can find it and know what it is for. Safewell lists a spill kit label for 120 litre kits and a set of basic spill kit instructions to keep with the kit. The instructions are a reminder, not a replacement for training.

For a wider look at the same idea, Safewell’s guide to chemical spill kit contents walks through a checklist for NZ workplaces.

Vehicle spill response kit

A vehicle or fleet kit is a smaller version of the same thing. The principle does not change: it must suit the biggest likely leak, which for a work vehicle is usually a fuel, hydraulic or engine oil leak. Keep gloves, eye protection, absorbent pads or socks, a drain guard, bags for used material and a copy of instructions in a bag or container that stays with the vehicle. Check it when you service the vehicle. Drivers who work alone also benefit from a first aid kit in the same vehicle, so Safewell’s lone worker and vehicle first aid kit sits well beside a small spill kit.

How to clean up a small oil spill at work

The steps below combine the EPA’s emergency guidance and Environment Southland’s spill procedure. Treat them as a template and check them against your own SDS and site plan.

  1. Put people first. Raise the alarm and keep others away. Identify the material and put on PPE. If the spill is flammable, remove ignition sources. The EPA says to move away from a flammable spill before using a phone, then call 111 and ask for Fire if the situation is beyond a small spill. Give the chemicals and quantities if you can.
  2. Stop the source, only if safe. Close a valve, plug the leak or turn the container upright. Do not take risks to do it.
  3. Protect drains and waterways. Confine the spill with socks, sandbags or booms and block access to stormwater grates, sumps and interceptors, as Environment Southland’s procedure sets out.
  4. Contain and absorb. Ring the spill with socks or barriers, then work absorbent pads or loose absorbent inward from the edge. Use a plastic shovel and broom to gather it.
  5. Do not use dispersants or emulsifiers. Environment Southland says to clean up without them, as they push oil further into the environment.
  6. Notify. Tell your supervisor. For anything that may reach the environment, contact the relevant agencies, such as Fire and Emergency or your regional council. Environment Southland lists a 24/7 Pollution Response Hotline on 0800 76 88 45 for its region. Other regions have their own council contacts.
  7. Bag and label the waste. Put used absorbent and contaminated PPE in the leak-proof container.
  8. Restock and review. Replace what you used immediately and review how the response went.

Disposal

Contaminated materials are disposed of as hazardous waste. The EPA’s guidance says to follow the SDS and any district council rules for hazardous waste. Product labels must also identify at least one appropriate and achievable disposal method, as required by the EPA’s consolidated Labelling Notice. Never wash residue into a drain.

Why the SDS matters

Every hazardous substance you hold needs a current SDS that workers and emergency services can easily get to. WorkSafe notes that section 6 usually gives full information on how to handle spills, and that you should ask your supplier for a new one if yours is missing or more than five years old. Keep a copy beside the kit.

Keeping the kit ready: a checklist

A kit that is empty, buried or unknown to staff fails when it is needed. Use this as a routine check, set to the schedule that fits your site:

  • The kit is in the place shown on your site plan and the label is readable.
  • The seal or lid is intact and nothing is damp or damaged.
  • PPE is present in the sizes your team wears, and nothing is past its use.
  • Absorbent capacity still matches your largest likely spill.
  • Drain guards, socks and barriers are all there.
  • Waste bags or containers are present and not split.
  • The SDS and instructions are with the kit and up to date.
  • Every worker who might use it knows where it is and how to use it. The EPA requires workers to know where the kit is kept and how to use it.
  • After any spill, replace used items at once. Environment Southland says to replace containment equipment and protective gear immediately and review your procedure.

Run a short drill once a year or when staff change. Ten minutes with the kit open on a bench teaches more than a page of instructions.

Getting the kit and the refills from one place

Most sites do not need to build a kit item by item. A ready kit sized for your volume, plus a PPE pack and labels for refills, keeps the list above short. Safewell’s catalogue covers spill management, first aid kits, medical equipment, safety and hygiene products and healthcare waste, with New Zealand-wide delivery. That means the spill kit, the first aid kit and the replacement items can go in the same order.

First Aid Kit Premium Lone Worker In Large Soft Pack Bag

Start with your worst-case spill from the sizing steps, pick the kit that covers it, and add the accessory pack so the PPE is in the same bag. You can see the full range on Safewell’s categories page.

FAQ

What is usually in an oil spill kit?

Expect PPE (gloves, goggles, overalls, gumboots), a broom and plastic shovel, absorbent pads, socks or loose absorbent, drain guards or barriers, and a leak-proof waste container. WorkSafe and the EPA both list these groups. Size the amounts to your largest likely spill.

How do you clean up a small oil spill?

Put on PPE, remove ignition sources, stop the leak if safe and block drains. Contain the spill with socks or barriers, absorb it from the edges inward, then bag the waste in a leak-proof container. Do not use dispersants, and restock the kit afterwards.

Can I use sawdust to soak up oil or fuel?

Not for flammable liquids. The EPA and WorkSafe both say sawdust acts as a fuel in a fire. Use absorbent pads, sand, vermiculite, zeolite or similar inert materials instead.

When should I call 111 instead of using the kit?

Call 111 and ask for Fire when a spill is large, flammable vapour is present, people are at risk or the spill is heading for a drain or waterway. A kit is for small spills that can be contained safely. Move away from flammable spills before using your phone.

Sources

This article was produced with AI assistance and reviewed for accuracy. It is provided for general information only and is not professional advice.