First Aid Kit Tamper Seals: How They Work in NZ Workplaces
A tamper seal is a small breakable tag, label or tie fitted across the closure of a first aid kit. If it is intact, nobody has opened the kit since it was last checked. If it is broken, the kit needs inspecting and restocking. That is the whole idea, and it saves a lot of time. Instead of opening every kit on site each month, you walk past them, spot the broken seals and deal with those first. Pair the seal with a dated inspection record and a kit that closes properly, and you have a simple system that keeps kits ready when someone is hurt. Our Generic First Aid Inspection Record Sticker A6 is made for the record half of that system.
TL;DR
- A tamper seal shows at a glance whether a kit has been opened since its last check. NZ Police policy uses a tie tag across the zips to identify a full, up-to-date kit.
- A seal does not replace checks. It tells you which kits to open first. You still check contents and expiry dates on a routine.
- WorkSafe expects a workplace to provide at least one kit, make sure workers know where it is, and protect the contents from dust, moisture and contamination.
- When a seal is broken: open the kit, check it against the contents list, replace what was used or has expired, record it, and fit a new seal.
- Pair every seal with a dated inspection record and a named person responsible for the kit.
Table of Contents
- What a tamper seal on a first aid kit shows
- Why seals matter under NZ workplace expectations
- Types of tamper seal and where each suits
- How to fit, check and replace a seal
- Who looks after the seals
- How often to inspect
- What to replenish when a seal is broken
- Common mistakes with tamper seals
- Seals at home and in community groups
- Getting the kit and records in place
- FAQ
- Sources
What a tamper seal on a first aid kit shows
A tamper seal is a single-use device. It cannot be removed without breaking, tearing or snapping it, so it can’t be put back to look untouched. That makes it a signal rather than a lock. It does not stop anyone opening the kit, and it shouldn’t: in an emergency, someone must be able to get in quickly. It simply records that the kit has been opened.
The value is in what the signal tells you:
- Intact seal: the kit was complete and in date at the last inspection, and nobody has dipped into it since.
- Broken seal: something may have been used, borrowed or moved. The kit needs a check and probably a restock.
- No seal at all: the last person to open it did not replace it, so you can’t tell what state it is in.
New Zealand Police provides a real-world example. Its first aid equipment policy says a full, up-to-date kit can be identified by using a tie tag to seal the zips closed. The same policy ties kit auditing to a site checklist completed at a set frequency. The seal makes the audit faster, because the person doing it can tell at a glance which kits are untouched.
Why seals matter under NZ workplace expectations
Under the Health and Safety at Work Act 2015, the business or undertaking (the PCBU, in WorkSafe’s terms) must give workers access to adequate first aid equipment. WorkSafe’s guidance on general risk and workplace management says adequacy is judged against the workplace, the workers, the hazards and what workers themselves say. A kit that was emptied last month and never refilled is not adequate, however good it looked on the day it was bought.
WorkSafe’s First Aid at Work page sets out the basics. A workplace must provide at least one first aid kit and make sure workers know where it is. Kits can be any size, shape or type, but should be labelled “First Aid Kit”, include a contents list and protect the contents from dust, moisture and contamination. The same guidance says the work’s risks should determine what goes in, with basic equipment for common injuries such as cuts, sprains, minor burns, broken bones, eye injuries and shock.
None of that mentions seals. WorkSafe doesn’t require them. What the guidance does require is a kit that is ready when needed, and a seal is one of the cheapest ways to prove it is. If you have several kits, such as a site office, two vehicles and a workshop, a seal turns an inspection round from a full unpacking exercise into a quick scan.
For workplaces that want a full picture of what to hold, see our guide to workplace first aid compliance in NZ. Construction sites have extra considerations, covered in construction first aid requirements in NZ.

Types of tamper seal and where each suits
Seals for first aid kits come in a handful of common forms. They differ in how they attach and how easy they are to snap by hand, which is the important point: a seal that needs scissors or a knife slows down someone treating a bleeding wound.
| Type | How it works | Best suited to |
|---|---|---|
| Tie tag or pull-tight tag | A plastic strap threads through the zip pullers or handle and locks in place. Pulled by hand to break. | Soft pack kits with zips, vehicle kits, bags |
| Adhesive label | A sticker spans the lid and body. Tears or shows damage when the lid lifts. | Plastic boxes and cabinets with lids |
| Numbered or coloured seal | Same as a tag, but with a number or colour so you can match it to a record. | Sites with many kits, auditing |
| Combined inspection label | A tamper-evident strip on top of an inspection record with a date and initials. | Small organisations wanting one item that does both jobs |
Choose by closure, not by price. A kit with zips takes a tag through the pullers. A rigid box with a lid takes a label across the join. If the kit has neither a hole to thread nor a flat surface to stick to, the seal won’t hold, so check how the kit closes before you pick.
Our range covers the kit types these seals go on. The Workplace 1-25 Plastic Wall Mountable First Aid Kit has a lid closure, while the Workplace 1-25 standard Soft Pack closes with zips. Soft packs are also available for 1 to 5 people, 1 to 15 people and 1 to 50 people.
How to fit, check and replace a seal
The routine is the same whichever type you use. The skill is in doing it every time the kit is opened, not just at the monthly check.
1. Check the kit before you seal it
Never seal a kit you haven’t checked. Compare the contents against the list inside the lid, make sure dressings are intact and in date, and replace anything missing. WorkSafe says kits should include a contents list, so use it. A sealed but half-empty kit is worse than an unsealed one, because the seal tells people it is ready.
2. Fit the seal across the opening
For a zipped soft pack, thread the tag through both zip pullers so the bag cannot open without the tag breaking, then pull it tight until it locks. For a lidded box, put the label across the join between lid and base, pressing both ends flat. Leave no gap that a hand could slip through.
3. Write the check on the record
Record the date, the initials of the person who checked it, and the seal number if you use numbered seals. An inspection record sticker on the kit or its wall mount keeps this in one place, where the next person will see it. If your seals are numbered, the number on the record should match the number on the kit.
4. Break it by hand when you need the kit
Anyone treating an injury should simply snap or tear the seal and get on with it. Nobody should have to hunt for scissors. After the emergency, the broken seal is your flag that the kit needs attention.
5. Restock, record and reseal
After use, the person responsible opens the kit, replaces what was used, checks expiry dates, records it and fits a new seal. Tell people to report any use, however small, so a broken seal is never ignored. If a kit turns up with a broken seal and no report, treat it as incomplete until it has been checked.
Who looks after the seals
WorkSafe’s guidance suggests a workplace nominates a person to maintain the first aid kits, such as a first aider, though it does not say the person must be one. In practice, pick someone who walks past the kits regularly and has the authority to order supplies. Put their name on the inspection record, so everyone knows who to tell when they use something.
Small teams often assume “someone” will handle the restock. A seal makes that harder to assume, because a broken one sits there in plain sight until somebody acts on it. Naming one person, plus a back-up for leave periods, is what makes the system work.
How often to inspect
WorkSafe’s guidance doesn’t set a national interval for checking kits. Your risk assessment decides it. For a sense of what organisations do, the University of Auckland says its kits should be checked at least monthly, including expiry dates. That is one institution’s practice, not a rule, but it gives a workable starting point for an office. A high-risk site such as a workshop, a construction site or a vehicle fleet may need more frequent checks.
Seals change what the check looks like rather than removing it. A practical routine:
- Weekly or fortnightly walk-round: look at every seal. Anything broken goes on a restock list.
- Monthly or risk-based full check: open the kits, check expiry dates and contents against the list, reseal and record.
- After any incident: check the kit used, whatever the schedule says.
If you want a ready-made prompt for your own routines, a caregiver emergency binder shows how to gather contacts and key information in one place, and the same thinking works for a workplace emergency folder kept beside the kit.
What to replenish when a seal is broken
A broken seal doesn’t tell you what was used. Check everything against the contents list, and look closely at the items most often taken. The University of Auckland’s guidance lists replacement supplies including wound dressings, triangular bandages, eye pads, plasters, gloves, tape, cleansing wipes, burn dressings, face shields, saline pods, shears, foil blankets and conforming bandages. Plasters, gloves and wipes tend to go first, so keep spares.
The same page says its kits must not contain medicines, creams or EpiPens. That is the university’s own policy and not a national rule, so decide what your kit holds based on your own risk assessment and, for anything medical, advice from a doctor or pharmacist.
Two habits keep restocking painless:
- Keep a small spares box. Hold spare dressings, plasters, gloves and wipes in a clear container, so a restock takes minutes. A clear 2 litre first aid box suits this well, as you can see what is inside without opening it.
- Match refills to the kit. Restock from the same supplier and list your kit came with, so what you replace matches what the contents list says should be there.
Common mistakes with tamper seals
- Sealing without checking. The seal then vouches for a kit nobody verified.
- Using a seal that is hard to break. If it needs tools, people will cut the zips or leave the kit alone.
- Ignoring broken seals. A broken seal that stays broken for weeks is the same as having no seal.
- No record. Without a date and initials, an intact seal says only that nobody has opened the kit, not when it was last checked.
- Forgetting vehicles and portable kits. These get opened most and checked least.
- Hiding the kit. WorkSafe says workers must know where the kit is, so keep it visible and labelled “First Aid Kit”.
Seals at home and in community groups
The same logic works outside a workplace. A sports club, a marae, a scout group or a school trip leader may pass a kit between several people, and none of them can easily tell whether it is complete. A seal and a date on the lid answer that question before the bus leaves. At home, a kit in the car or the caravan benefits from a seal if you want to be sure it is ready for the summer holidays. Our home first aid preparedness guide covers what a household kit should hold.
Getting the kit and records in place
A seal works best on a kit that already suits your site. Our first aid kits range covers workplace and industry kits sized to different team numbers, with first aid supplies for refills, and New Zealand-wide delivery. Pair a kit with an inspection record sticker so each check is dated and initialled where the next person will see it. You can browse everything on our categories page, or start from the Safewell homepage.
FAQ
What is a tamper seal on a first aid kit?
It is a single-use tag, tie or label fitted across the kit’s closure. It breaks when the kit is opened, so you can see at a glance whether the kit has been used since its last check. It indicates that a check is due, but it does not lock the kit.
Does WorkSafe require tamper seals on first aid kits?
No. WorkSafe’s guidance requires a kit suited to the work’s risks, labelled, with a contents list and protected from dust, moisture and contamination. Seals are an easy way to show the kit is still complete, but they are your choice.
How often should I check a sealed first aid kit?
WorkSafe doesn’t give a national interval, so base it on your risks. One example is the University of Auckland, which checks its kits at least monthly. Walk past sealed kits more often to spot broken seals, and open each one for a full check on your set schedule.
What should I do when I find a broken seal?
Open the kit, check it against the contents list, replace anything used or out of date, record the check, and fit a new seal. Ask the person who used it to report what they took, so you restock the right items.
Can anyone break the seal in an emergency?
Yes, and they should. A good seal snaps or tears by hand, so nobody is delayed. Treat the casualty first, and report the use afterwards so the kit can be restocked.
Sources
- WorkSafe NZ: First aid at work
- WorkSafe NZ: General risk and workplace management
- New Zealand Police: First aid training and equipment kits
- University of Auckland: First aid kits and defibrillators
Recommended
- Workplace First Aid Compliance in NZ: What You Must Have
- Construction First Aid Requirements in NZ: Kits, People, Training
- Managing First Aid Kit Expiry: A Practical NZ Guide
This article was produced with AI assistance and reviewed for accuracy. It is provided for general information only and is not professional advice.
