Chemical Spill Kit Contents: A Checklist for NZ Workplaces

A chemical spill kit should hold PPE, containment gear, handling tools, absorbents that suit your chemicals, and a leak-proof container for the waste. In New Zealand, the contents have to match the hazardous substances you keep, how much of them you hold and what their safety data sheets (SDS) say. A generic kit is a starting point, not a guarantee.

This guide gives you the checklist, explains how to choose PPE and absorbents, and covers what to do during and after a spill.

Safewell
Match Your Spill Kit to Your Workplace
Safewell provides spill kit management solutions and medical supplies for trades and workplaces across New Zealand.

TL;DR

  • A chemical spill kit needs five groups of items: PPE, containment, handling tools, compatible absorbents and a sealed waste container.
  • Build the kit from your SDS and inventory. The right contents depend on the substance and the likely spill size.
  • Stock enough PPE for every person who might respond, and train them to use it.
  • Sawdust is unsuitable for flammable or oxidising substances because it can fuel a fire.
  • Restock straight after any use, and review why the spill happened.

Table of Contents

What a chemical spill kit is for

A chemical spill kit lets a trained person contain and clean up a small to moderate spill without putting themselves at risk. It is not a tool for every emergency. New Zealand’s hazardous substances guidance ties the kit to the substances present, their quantities and the SDS, and notes that specialist controls may be needed for some of them.

That is why a kit labelled “chemical” is only suitable for the chemicals it is designed for. Before you buy, list what you store and read each SDS. A workshop with solvents and cleaning products has different needs from a lab with acids, or a farm shed with agrichemicals.

If your main risk is oil, fuel or other hydrocarbons, a dedicated kit is a better match. Our oil and hydrocarbon spill kits are one example. For mixed or unknown liquids, see the chemical and general purpose spill kits.

Chemical spill kit contents checklist

WorkSafe New Zealand’s spill kit guidance and the hazardous substances guide above point to the same core groups. Use this as your checklist.

Group What to include Why it is there
PPE Gloves, overalls, gumboots, goggles, respirator or facemask Protects the person cleaning up
Containment Drain guards, barriers, drip trays or pans, absorbent socks Stops the spill spreading or reaching drains
Handling tools Broom, plastic shovel or scoop Moves absorbed material without sparks or reactions
Absorbents Pads, socks, or inert material such as dry sand, vermiculite or zeolite Soaks up the liquid
Waste Leak-proof container, heavy-duty bags, ties, labels Holds contaminated material safely
Information Instruction sheet, SDS folder, emergency numbers Guides the response

Two practical points. First, WorkSafe says the kit needs enough PPE for the number of workers who may have to manage the spill. One pair of gloves in a kit used by a team of six is not enough. Second, plastic tools are listed for a reason: they are less likely to react with or spark around what you are cleaning up.

Items worth adding

These depend on your site, but many workplaces add:

  • Spare gloves in more than one material, since no single glove suits every chemical
  • A torch and a roll of hazard tape to mark off the area
  • A notepad or incident card to record what was spilled, where and when
  • Spare bags and a sealable bucket for small items such as used PPE
  • A laminated one-page response plan taped inside the lid

Choosing PPE for chemical spills

PPE is the part of the kit most often under-specified. WorkSafe’s guidance says to consider the substance, the airborne concentration and the hazard information on the label or SDS. The PPE must be suitable, fit properly and meet New Zealand or Australian Standards where they apply.

Gloves

There is no universal chemical glove. The University of Auckland’s laboratory quick reference guide says to choose gloves using the SDS and glove-safety charts. It also says to change them immediately if they are contaminated, torn or punctured, and not to reuse them. Keep spares in the kit so that swap is possible mid-clean-up.

Eye and face protection

Goggles are the usual choice in a spill kit because they seal around the eyes against splashes. The same Auckland guide requires safety glasses in labs unless a risk assessment finds them unnecessary. For a spill response, where splashing is likely, goggles are the safer default.

Body and feet

Overalls and gumboots are on both the WorkSafe and hazardous substances lists. They keep chemicals off skin and clothing, and the boots are easy to rinse or discard. Make sure the sizes suit your people, because ill-fitting PPE is a hazard of its own.

Respirators

Respirators or facemasks are listed where vapours or dust are a risk. The type of filter depends on the chemical, so check the SDS. Fit and training matter here: a respirator that does not seal properly gives false confidence. Our guide on choosing PPE for different professions covers the wider range of protective gear.

Under New Zealand’s hazardous substances guidance, the business must provide the required PPE and make sure workers are trained to use, maintain, clean and store it.

Matching absorbents to your chemicals

The absorbent is where “one kit fits all” thinking goes wrong. WorkSafe’s list names inert options such as dry sand, vermiculite, zeolite and containment socks. Pads and socks come in different types, so check that the type in your kit suits your chemicals: general purpose, chemical or oil-only.

Some rules of thumb:

  • Flammable or oxidising liquids: do not use sawdust. The hazardous substances guide warns that it can act as fuel in a fire.
  • Acids and alkalis: check the SDS for compatible absorbents. Some products are formulated to neutralise specific chemicals, and they should only be used for what they are made for.
  • Unknown liquids: treat the spill as hazardous. Do not mix absorbents or try to guess. Evacuate and get advice.
  • Oil and fuel: use hydrocarbon-rated absorbents, which are designed to pick up oil-based liquids.

If your site holds several chemical types, consider more than one kit, each labelled for what it covers, rather than one kit that half-suits everything.

Sizing the kit and placing it

WorkSafe’s service station guidance says kit equipment depends on the substances and the possible spill quantity. A practical way to size a kit:

  1. List every hazardous substance and its largest container.
  2. Work out the worst plausible spill, for example a dropped 20 litre drum.
  3. Pick a kit with absorbent capacity to match, with some margin.
  4. Place it close to where spills are likely, but not so close that a spill would block access to it.
  5. Mark the location clearly and tell everyone who works there.

Kits are sold by absorbent capacity in litres. Our 50L general purpose spill kit suits small to moderate spill risks. Larger sites and bulk storage need larger capacity or several kits spread around.

Spill response steps

The kit is only useful if people know the order of actions. These steps draw on WorkSafe’s emergency guidance and the University of Auckland’s spill procedure.

Minor spills

  1. Clear the area and get help.
  2. Find the SDS and identify the substance, if it is safe to do so.
  3. Put on the PPE that suits the substance.
  4. Stop the source if it is safe to do so.
  5. Contain the spill and protect drains and waterways.
  6. Clean up with compatible absorbents.
  7. Bag and seal the waste.
  8. Tell your supervisor or manager.

Major spills

For a major spill, evacuate and call for capable help. Remove ignition sources only if it is safe. WorkSafe says to raise the alarm, call 111 and ask for Fire when appropriate, and not to endanger yourself. Responders should refer to the SDS or a certified handler or specialist for advice.

An important point for managers: WorkSafe’s emergency response policy states that Fire and Emergency New Zealand leads hazardous-substance emergencies once it arrives and takes control. So the workplace should not assume it stays in charge of a serious incident. Your job is to keep people safe, hand over clear information and have the SDS ready.

Major spill alarm and emergency handover sequence

Disposing of contaminated waste

Used absorbents are hazardous waste until proven otherwise. The University of Auckland’s procedure says to seal spill-kit items and other contaminated products in plastic bags or containers, then take them to an authorised disposal point with a hazardous-waste declaration, or contact an authorised waste contractor.

The EPA’s disposal notice covers hazardous substances and containers that have been in direct contact with them. It says health-hazard and metal-corrosive substances generally must be treated, discharged under specified conditions or exported as waste. For health hazards other than skin or eye irritation or corrosion, dilution does not count as treatment before discharge. In plain terms: do not wash spilled chemicals down the drain.

Keep a labelled, leak-proof container in the kit so waste is contained from the moment you finish. Our range of healthcare waste and containment supplies covers bags and containers for that stage.

Sealed container holding bagged contaminated absorbents

If you run a business or undertaking (a PCBU), the hazardous substances guidance says you must:

  • Prepare an emergency response plan
  • Provide the PPE workers need
  • Keep a hazardous substance inventory and the SDSs
  • Make sure workers get information, training and instruction

WorkSafe’s service station guidance adds that the plan must cover every reasonably foreseeable hazardous-substance emergency, and that workers must be trained in emergency actions and the safe use of equipment, including PPE.

There is also a reporting duty. The Health and Safety at Work Act 2015 includes in a notifiable incident an unplanned or uncontrolled escape, spillage or leakage that exposes or could expose someone to serious risk. A PCBU must notify the regulator as soon as possible after becoming aware of a notifiable event. If you are unsure whether a spill qualifies, ask WorkSafe or your health and safety adviser straight away.

Inspecting and restocking the kit

A kit with empty gloves boxes and dried-out pads fails when you need it. A routine check works well:

  • Monthly: check the seal or lid, and confirm the kit is where it should be and not blocked.
  • Quarterly: count PPE against the number of people who might respond, and check sizes.
  • Every check: look at any expiry dates on products, the condition of bags and tools, and whether the instruction sheet and SDS folder are current.
  • After any change in chemicals stored: reassess whether the absorbents and PPE still suit.

After a spill, restock the kit and review what went wrong. The University of Auckland’s procedure says to restock, assess the reasons for the incident and put a corrective response in place as soon as practicable. Treat that as part of readiness, not paperwork. Refill items, gloves and bags can be reordered individually from our first aid and safety supplies, so you rarely need to replace a whole kit.

Spill kits from Safewell

Safewell supplies spill management products for New Zealand trades, workplaces and community organisations, with delivery nationwide and support for both full kits and refill items. You can start with our spill kits and spill management supplies page, or go straight to the chemical and general purpose spill kits.

Sharps and Bio Hazard Waste Personal Containment Kit 200ml

Before you order, have your SDSs and chemical list to hand. Match the kit to your substances, check that the PPE covers your team, and add refills for anything you expect to use up quickly.

FAQ

What chemicals can you use a spill kit on?

Only those the kit is designed for. Check the kit’s labelling against the SDS for each substance you hold. Flammable, oxidising, highly toxic or unknown chemicals may need different absorbents or specialist help, so evacuate and call for advice if you are unsure.

What are the steps to clean up a chemical spill?

Clear the area, get help, identify the substance from its SDS, and put on suitable PPE. Stop the source if it is safe, contain the spill and protect drains, then clean up with compatible absorbents. Seal the waste, dispose of it through an authorised route and tell your supervisor.

Can I use sawdust or kitty litter as an absorbent?

Not for every chemical. New Zealand guidance warns that sawdust can act as fuel with flammable or oxidising substances. Use inert absorbents that suit the chemical, as set out on its SDS.

How much PPE should a chemical spill kit hold?

Enough for everyone who may need to respond, as WorkSafe advises. That usually means several pairs of gloves, goggles and overalls in the right sizes, plus a respirator or facemask where the SDS calls for one.

When does a spill have to be reported to WorkSafe?

When it is a notifiable event, such as an uncontrolled spill that exposes or could expose someone to serious risk. The Health and Safety at Work Act 2015 requires notification as soon as possible after you become aware of it.

Sources

This article was produced with AI assistance and reviewed for accuracy. It is provided for general information only and is not professional advice.